Related Manuals for Presenza QKA051
Summary of Contents for Presenza QKA051
- Page 1 DELUXE STAINLESS STEEL HANDCRAFTED WORK CENTRE SINK KIT INSTALLATION GUIDE AND USER MANUAL ITM. / ART. 40801 Model No. QKA051...
-
Page 2: Table Of Contents
If you have any questions, contact the manufacturer . 3 . Installation work and plumbing must be done by qualified person(s) in accordance with all applicable codes and standards . 4 . Protect the entire surface during installation . QKA051... -
Page 3: Warranty
Warranty TEN YEAR LIMITED WARRANTY A thorough inspection must be made before installation and any damage must be promptly reported . We will not be liable for failures or damage that could have been discovered or avoided by proper inspection and testing prior to installation . Our goods come with guarantees that cannot be excluded under the Australian Consumer Law . -
Page 4: Pre-Installation
Hacksaw screwdriver Safety goggles Safety gloves PARTS REQUIRED (NOT INLCUDED) Plastic Connecting NOTE: flange (1) Tail pipe (1) nut (1) Supply lines (2) Parts not shown to actual size. (3 .8 cm dia .) (3 .8 cm dia .) QKA051... -
Page 5: Package Contents
Pre-Installation (continued) PACKAGE CONTENTS Part Description Quantity Undermount Sink Template Undermount Sink Template Topmount Sink Template Stainless Steel Sink Bottom grid Sliding sink Faucet Colander Bamboo cutting board Topmount clips Undermount clips Strainer Strainer Assembly CONGLOMKB .COM Please contact cs@conglomkb.com or +61 2 87245218 for further assistance . - Page 6 - Make sure the template (1A/1B) is parallel to the front of the counter . 8.9 cm - 10.2 cm Tape Tape Faucet will be installed on sink deck Faucet will be installed on countertop QKA051...
- Page 7 Installation (continued) DRILLING THE HOLES FOR THE UNDERMOUNT TESTING THE FIT OF THE SINK CLIPS - Place the sink (A) underneath the cut-out in the counter to test its fit. Ensure that the reveal is equal on sides 1 and 3 when viewed from above .
- Page 8 SUPPLY LINES (NOT INCLUDED) The supply lines, which connect the faucet to the household water system, are not supplied with this unit . They need to be purchased separately . Follow the supply line manufacturer’s instructions for proper installation . QKA051...
- Page 9 Installation (continued) TOPMOUNT INSTALLATION PREPARING THE AREA CUTTING THE COUNTER NOTE: CAUTION: Always wear safety goggles and gloves when Topmount sinks are dropped into the counter from above. If you are using power tools to prevent personal injury . installing an undermount sink, please see “undermount installation” on page 6.
-
Page 10: Topmount Clips
SUPPLY LINES (NOT INCLUDED) The supply lines, which connect the faucet to the household water system, are not supplied with this unit . They need to be purchased separately . Follow the supply line manufacturer’s instructions for proper installation . QKA051... - Page 11 Installation (continued) INSTALLING THE STRAINER - Apply a small amount of plumber’s putty (not included) in the notch around the drain hole of the sink . - Connect the upper strainer body (K2) and the strainer ring (K3), and insert them into the drain hole from the top of the sink .
-
Page 12: Operation
- The bottom grid (B) must be positioned with its rubber supports down . Tilt the grid up so it is at a slight angle, slide it into the sink (A), and place it so that it is sitting flat on the bottom of the sink . QKA051... -
Page 13: Care And Cleaning
Care and Cleaning SINK, SLIDING SINK AND COLANDER CUTTING BOARD - After use, always rinse your sink with tap water to dilute and - Before using your new bamboo cutting board, oil with remove deposits . mineral oil . Apply oil to your cutting board with a cotton cloth . -
Page 14: Service Parts
6:30 am - 3 pm AEDT Monday - Friday . Identify the required part(s) and have the part number(s) ready . Part Description Code Quantity Bottom grid QHS213 Bamboo cutting board QHS210 Strainer QHS214 Strainer assembly QHS148 Topmount clips QHS108 Undermount clips QHS109 Sprayer head QHL149 Ceramic cartridge QHS121 Faucet lever QHL148 QKA051... - Page 15 Imported by: Conglom International Unit 101B, Block A Dublin Airport Business Park, Swords Road, Santry. D09 H5R7 Ireland +61 2 87245218 | cs@conglomkb.com (service available Monday - Friday from 6:30 am - 3 pm AEDT) www.conglomkb.com Made in China Retain this manual for future use.